← Australian Superyachts: Pittwater Bank WhatsApp Discuss your draft and timing

Pittwater Bank off West Head: 3D depth model

By Australian Superyachts. Seabed: NSW Marine LiDAR Topo-Bathy 2018, and inside its coverage the Transport for NSW multibeam survey of 25 to 29 October 2021. Spot soundings: Australian Superyachts vessel survey, 1355 soundings on 5, 14 and 16 November 2026. Depths in metres below chart datum. Set your tide and draft below to see where your vessel can go.

NOT FOR NAVIGATION. General information only. Actual water levels can differ from predicted tides, and the seabed changes. This model does not replace official charts or good seamanship. Use at your own risk. Read the full disclaimer.
How to use this model
  1. Set the height of tide. Look up the predicted height of tide for Pittwater (for example Mackerel Beach or Palm Beach) at the time you plan to cross, in metres above chart datum, and move the Height of tide above chart datum slider to that value. Do not use the Sydney (Fort Denison) heights: on the survey days they ran about 0.2 m higher than the Pittwater predictions this model was reduced with, which would overstate the water. If you will cross over a period of time, use the lowest height expected during the crossing.
  2. Set your draft and margin. Move the Draft of your vessel slider to your deepest static draft. Then set Your clearance margin to the under-keel clearance you choose to keep. The margin is your decision as master; the model does not suggest one. With the draft at zero the red is switched off.
  3. Read the colours. Red seabed has less static water than your draft plus margin at that tide. Blue has more; darker blue is deeper. Blue is not a safe area: the model compares static depth only. Keep clear of the edges of the red.
  4. Check the bank. The line under the draft slider gives the water under your keel on the bank leg (186 degrees true, the magenta line from BAR N to BAR S 186) across the shallowest part of the bank, both for the typical depth and for the shoalest soundings recorded.
  5. Hover for depths. Move the mouse over the seabed to see the depth at that point at your tide, and the water under your keel. Hover over a coloured dot to see a measured sounding.
  6. Change the view. Use Oblique, Down the channel, Across the bank or Top down. Drag to rotate, scroll to zoom, right-drag to pan. Vertical exaggeration stretches depths so the shape of the bank is visible; real slopes are much gentler.
  7. Show or hide layers. Australian Superyachts Sounding Tracks shows the survey vessel's tracks, Spot Soundings the measured depths, TfNSW 2021 Multibeam the soundings from the Transport for NSW multibeam survey of October 2021, two rows of contour buttons switch depth lines from 2.5 to 5.0 m on or off, one by one, every 0.25 m: Available water lines show depth at your tide (white whole metres, dark half metres, thin pale blue quarter metres); Charted depth lines (amber and orange) show depth below chart datum, as printed on a nautical chart, and do not move with the tide. The red pile is Port beacon 002 off Observation Point and the yellow buoy is "YRM" (a special mark), and Water surface the sea level at your tide. Leg on seabed draws the route in bright green on the seabed itself, with pins up to the waypoints, so it lines up with the contours from any angle. The magenta dashed line is the bank leg, shown for reference only.
  8. On a phone or tablet, tap instead of hovering and use two fingers to zoom. A larger screen is easier.
about 3.5 m
bank leg 186°T, typical depth on the shallowest part, at this tide
3.3 m
shoalest soundings near the bank leg, at this tide
1355
Australian Superyachts soundings, November 2026
Depths, red area, contours and hover readings all follow this tide.
Red seabed has less water than your draft plus margin at the selected tide. Blue is deeper.
Your chosen under-keel clearance. The model does not recommend one.
Available water contours, depth at your tide (tap to show or hide):
Charted depth contours, below chart datum (LAT) as on a nautical chart, not tide-adjusted:

Static depth only. The model illustrates static depth relationships only. It does not allow for squat, vessel motion, swell, actual water level or survey uncertainty, and it does not determine whether a vessel can safely cross the bank. The margin you set is your own and does not establish safe passage. The master remains responsible for the vessel.

Bank leg 186°T (about 975 m): BAR N 33°35.124′S 151°18.624′E to BAR S 186 33°35.647′S 151°18.558′E. On the shallowest part of the leg the typical depth is about 3.5 m and the shoalest soundings about 3.3 m below chart datum. The bank is a broad, flat sand sill; for about 100 m either side of the leg the depths are within about 0.1 m of these, which is the limit of what this survey can resolve.
About the data: the coloured seabed and the contours are from the 2018 LiDAR survey, except in the strip just east of the bank leg covered by the Transport for NSW multibeam survey of October 2021 (survey 717-033), where the seabed is built from that survey's soundings (TfNSW 2021 Multibeam button). The 2021 multibeam reads about 0.14 m shallower than the LiDAR, and our 2026 soundings within 5 m of a 2021 multibeam sounding are within about 0.2 m of it on average (spread about 0.25 m). A check against water levels recorded at the Patonga tide gauge on 14 and 16 November 2026 suggests our soundings, and the depths in this model near the bank leg, may be about 0.2 m shallower than shown on the official datum (0.925 m below AHD). Allow an extra 0.2 m, particularly if you use Bureau of Meteorology or Fort Denison tide heights. The dots are soundings taken by Australian Superyachts in November 2026 with a single-beam echo sounder, corrected for tide; the soundings read about 0.1 m shallower than the LiDAR, so treat the LiDAR depths as slightly optimistic. Areas between the survey lines were not sounded. Land heights are compressed for display. Model version: November 2026.

Disclaimer: read before use

Not for navigation. This 3D model is published by Australian Superyachts Pty Ltd for general information and preliminary assessment of the entrance only. It is not a nautical chart, navigational product or approved passage-planning document. It has not been produced, checked or endorsed by the Australian Hydrographic Office, Transport for NSW or any other hydrographic or maritime authority, and it must not be used for navigation.

By using this model you accept these terms.

Not for navigation

This model is general information only. Depths come from a small private survey, 2018 LiDAR and a 2021 multibeam survey, the seabed moves, and real water levels can differ from predicted tides because of weather and other conditions. It does not replace official charts, good seamanship or the skipper's judgement.

Australian Superyachts accepts no responsibility for its use. You use it entirely at your own risk.

Read the full disclaimer